For the cockpit, apron, and airfield Open-source firmware

Your flight picture Close at hand

Pilot Kit Box is a portable AHRS (Attitude and Heading Reference System) flight companion with open-source firmware, bringing together attitude and heading reference, GNSS positioning, barometric altitude, traffic awareness, and flight recording. Check your flight picture on one screen, listen to airband radio, and revisit the journey after landing.

Pilot Kit Box with a map display in a C172 cockpit
Inside the box

From display to antenna

An exploded view of Pilot Kit Box: touchscreen, expansion board, battery, enclosure, antennas, and speaker.

Pilot Kit Box system exploded view: touchscreen, expansion board, battery, enclosure, antennas, and speaker
What it does

Your flight picture, close at hand

In the cockpit, on the apron, or watching aircraft at the airfield: see your position and nearby traffic, listen to radio calls, and keep a record to revisit.

Attitude, heading, and position

See attitude and heading reference, GNSS position, and barometric altitude on the built-in screen. Keep these flight references together in a portable device.

Nearby traffic at a glance

View received aircraft on the traffic radar, map, or list. In the cockpit or at the airfield, follow where surrounding traffic is moving.

Listen to the airfield

Tune to tower, approach, or airfield frequencies. Listen through the device and replay saved airband recordings.

Revisit the flight

Save flight tracks and radio recordings to microSD. After landing, look back at the route and listen again to the calls along the way.

Application scenes

Pilot Kit Box with a map display in a C172 cockpit
Pilot Kit Box with a map display beside a DA40 on the apron
Pilot Kit Box with a traffic radar display beside runway 27
Pilot Kit Box with an airband display on grass
Hardware

Hardware designs you can explore

A six-layer integrated expansion board connects to the Waveshare ESP32-P4 carrier as a HAT, bringing reception, sensors, and power together without an RTL-SDR dongle. Board size: V4 100 × 62 mm; v5 100 × 79 mm. v5 integrates 1090/978 MHz IFA antennas and an internal GNSS antenna. Schematics, the KiCad project, and fabrication files are on GitHub.

Pilot Kit Box G1000-style primary flight display on the 4.3-inch touchscreen
Pilot Kit Box aircraft list showing nearby ADS-B traffic
Pilot Kit Box 360° traffic radar with offline map
Pilot Kit Box diagnostics page with live subsystem cards
Pilot Kit Box G1000-style primary flight display on the 4.3-inch touchscreen
Pilot Kit Box aircraft list showing nearby ADS-B traffic
Pilot Kit Box 360° traffic radar with offline map
Pilot Kit Box diagnostics page with live subsystem cards
Host board
Waveshare ESP32-P4-WIFI6-Touch-LCD-4.3 (ESP32-P4 32 MB + ESP32-C6, 4.3" 800×480 touchscreen)
Expansion board
V4.11, 6-layer 100 × 62 mm HAT, 231 placements / 506 vias
Receivers
1090 MHz ADS-B + 978 MHz UAT + 118–137 MHz airband AM, independent chains
Antennas
V4: on-board 1090 MHz IFA; v5: on-board 1090/978 MHz IFA and internal GNSS antenna. U.FL ports for external antennas.
GNSS
4-constellation (GPS / BeiDou / GLONASS / Galileo), internal patch / external switchable
Sensors
IMU attitude (100 Hz fusion), barometric altitude & vertical speed, magnetometer
Display
4.3" 800×480 MIPI-DSI touchscreen, G1000-style PFD / radar / map / airband UI
Connectivity
BLE GDL90 (ownship / traffic / heartbeat) today, Wi-Fi UDP GDL90 landing next; microSD logging
Pilot Kit Box enclosure exploded view: base, front frame, protective armor, SD door, and SMA antenna cover
Enclosure design

Five generations of board design

From the first carrier board to ongoing development, explore how Pilot Kit Box hardware has evolved.

Pilot Kit Box — First four board generations
First four board generations
Pilot Kit Box — v5 · Fifth-generation board v5
v5 · Fifth-generation board
v1
2.4-inch carrier with plug-in modules and an on-board 1090 antenna revision.
v2
RTL-SDR cutout board for the Waveshare 4.3-inch display.
v3
Integrated expansion board without an external SDR.
v4
Power section added and board layout refined.
v5 in internal development

Latest updates

  • The v5 six-layer board design and fabrication and assembly documentation are in place. Antenna and reception designs have been refined, adding an internal GNSS antenna and a 978 MHz IFA antenna. Enclosure structure and assembly design continue to be refined.

Inside the firmware

Instruments, radio, recording — all implemented

From dual-chain radio reception through traffic fusion, display rendering, and GDL90 streaming — all implemented and running on fabricated hardware today.

Reception & decode

  • 1090 MHz Mode-S decode via RP2040 PIO, dump1090-derived
  • 978 MHz UAT reception, fused into the same traffic table
  • 118–137 MHz airband AM reception with I²S audio capture
  • 4-constellation GNSS with PPS + RMC time discipline

Display & UI

  • G1000-style PFD: attitude, HSI, altitude/speed tapes
  • 360° traffic radar: heading-up / north-up, 2/5/10/20 NM
  • Offline aviation map with airport / navaid / FIX overlay
  • Touch navigation grid with full Chinese & English UI

Airband & recording

  • Airband listening with channel list and direct frequency entry
  • Recordings browsed and replayed on-device with volume control
  • 1 Hz flight-track logging with flight-phase detection
  • dump1090-compatible logs to microSD — pull the card and read it

Connectivity & data

  • BLE GATT: GDL90 ownship / traffic / heartbeat / time sync
  • GDL90 over Wi-Fi UDP in development — firmware work only
  • Works with Garmin Pilot, ForeFlight, and other EFBs
  • Two-stage clock discipline: BLE coarse + GNSS fine sync
Bill of materials

Off-the-shelf parts, a fraction of commercial boxes

A stock Waveshare carrier board plus one integrated expansion board replaces a pile of modules, dongles, and wiring. Commercial portable ADS-B receivers run $200–700; building Pilot Kit Box costs a fraction of that. Actual cost varies with supplier and region.

vs commercial portable ADS-B receivers

Comparable cost

  • Waveshare ESP32-P4-WIFI6-Touch-LCD-4.3 Carrier board with P4, C6, 4.3" touchscreen and touch controller
  • Pilot Kit avionics expansion board V4.11 6-layer integrated board: dual receive chains, sensors, power — fabricate it or assemble it yourself
  • microSD card Flight tracks, airband recordings and offline maps live on the card
  • 3.7 V 4000 mAh Li-po battery Standard portable battery, 5+ hours of runtime (measured ~606 mA average draw)
  • 3D-printed enclosure Printable split design with GPS tray — source files on GitHub
  • Optional external antennas V4 has an on-board 1090 MHz IFA; v5 adds a 978 MHz IFA and an internal GNSS antenna. Choose external antennas for the corresponding board.
Full BOM, suppliers, and cost reference on GitHub →
Integration

Pairs natively with the Pilot Kit App

Connect the Box to your phone over BLE in seconds. The Box streams GDL90 Ownship, Traffic, Heartbeat, and Time Sync over BLE GATT, and the Pilot Kit App subscribes automatically. Own-ship position, nearby traffic, barometric altitude, and precise timestamps flow continuously back to the App, enabling richer flight logs, full replay, deeper analysis, and easy sharing.

    GDL90 Ownship Traffic Heartbeat Time Sync
Pairs natively with the Pilot Kit App Pilot Kit Box BLE GATT Pilot Kit App
Firmware and design files

Understand it. Make it your own.

The firmware is open source under AGPL-3.0-only. Hardware and enclosure designs are publicly available under CC-BY-NC-SA-4.0 for noncommercial use. Explore the code, follow the design, and contribute within those terms.

See how it works

Read the firmware behind the instruments, traffic display, and recordings. The implementation is available on GitHub.

Build from published designs

Schematics, board files, and printable enclosure files are available under CC-BY-NC-SA-4.0. Follow the published design for a noncommercial build.

Use it alongside Pilot Kit

Keep the Box in your cockpit or airfield kit, with Pilot Kit on your phone for the rest of your flying workflow.

Follow the project

Browse development updates, report issues, and contribute firmware changes under AGPL-3.0-only.

A portable companion for pilots and aviation enthusiasts, with open-source firmware and publicly available hardware designs.

Safety & certification boundary

Pilot Kit Box is an open-source prototype and situational-awareness device.

This project does not represent FAA, EASA, CAAC, TSO, or other airworthiness certification.

Do not use it as a primary flight instrument, backup flight instrument, navigation source, or collision-avoidance system.

Flight decisions must remain based on certified avionics, installed instruments, visual scan, and applicable regulations.

Frequently asked questions

Get involved

Take a closer look at Pilot Kit Box

Explore the firmware and hardware designs, follow the project, or flash the firmware to your device.